- 08-20-2013, 01:24 PM #1
So I picked up an otterbox case earlier today and I decided that I would try and mod the case so I can wirelessly charge my phone. The tools I needed were: a hair dryer, xacto knife, double sided tape (the type for electronic components), and finally a Nokia wireless charging cover. To begin, I used the blow dryer to loosen up the interior lining of the charging cover. It is quiet easy to pull off by simply sliding the knife underneath the lining by the edge of the seem. I used the above technique to pry off the charging coil and contact points. I then peeled off the thin foam lining the interior of the otterbox case. I then placed some double sided tape on the charging coil and contact points. I carefully lined up the contact point on the phone and taped it down so it wouldn't move. Then I carefully placed the bottom part of the otterbox case on the phone and pushed down with firm pressure. When I removed the case, the coil and contact point were firmly in place. I placed the phone back in attached the rest of the case on, it fit nicely, then I tested it out. Success! To finish it off I removed the phone from the case and place the lining over the charging coil. All in all it was a nice project and worked great. Now I don't have to take the otterbox case whenever I want to charge the phone wirelessly. Any questions feel free to ask.
- 08-20-2013, 01:46 PM #3
Lol, it took less than 30 minutes and you can substitute the knife with something rigid and thin. I only tried this because I had 2 wireless charging covers, one that I received for free from the Microsoft store. But I figured I'd inform everyone that it is possible and if you want to make the investment its worth it.
- 08-20-2013, 02:00 PM #5
I placed it on the phone first, ensuring the contacts touched. I placed some double sided tape on the coil and then carefully placed the otterbox case on the phone. Picture this is this order, phone faced down, charging coil on top properly aligned, then the otterbox case placed on top. I guess I should have video taped the whole thing, lol
- 08-20-2013, 05:10 PM #6
The case works perfectly with the Nokia charging pad. Now it doesn't seem to be able to hold a connection with my energizer 3 position charging pad. Some things I noticed, the 1020 didn't seem to charge to well on the energizer pad with an unmodified Nokia cover, my 920 worked great. Now I believe that this might be due to the fact that the charging coil on the 920 is slightly thicker and bigger than the one for the 1020. Hope this info helps someone out.
- 08-21-2013, 02:39 PM #7
So I just read the article posted here that showed how to install the wireless charging pad directly into the Lumia 925 and I got to thinking, maybe I can do the same. Well after watching a disassemble video for the Lumia 1020, I must say it doesn't look possible. Everything is put together very tightly with no visible space for anything extra. Also everything needs to be removed separately to get to the battery which is located all the way in the bottom. So it seems I will not be doing that. Here is the link if any one is interested
On a lighter note it seems that the lcd is pretty easy to replace.
- 08-29-2013, 09:55 AM #8
I was literally trying to figure this out 5 minutes before I saw this post. I love my 920's Otterbox but I've been hesitating on buying the 1020 because I now have 3 wireless charge bases (one in the kitchen, one at work, one beside my bed) and I detest wire charging now. My primary concern would be one of heat dissipation, especially since your last step is basically insulation (which might be a good thing for the phone itself). Have you noticed any heat build up in excess of what you would get from a 920 charging?
- 08-29-2013, 07:24 PM #11
- 08-29-2013, 11:40 PM #12
I was thinking of installing it internally also. I found someone selling the 1020 shell on ebay. Maybe mod the shell before breaking your phone.
New Original Battery Back Door Cover for Nokia Lumia 1020 Nokia Elvis | eBay
- 09-05-2013, 06:47 PM #15
I haven't had time to try and experiment with installing the coil internally. Here are some images of my L1020 in a third party case with the working Qi coil. I purchased a clear Poetic Atmosphere Case from Amazon to help show the working coil. Also here are some images the Nokia Wireless Charging Case dissembled with Hot Hair-Dryer.
10-05-2013, 02:14 PM #21
- 3 Posts
10-20-2013, 12:19 PM #24
- 11 Posts
I modified my Otterbox Defender/Nokia Charging cover yesterday, but I made a couple of changes to correct the shortcomings that I found in the original charging cover design. It works great!
First off... I was afraid that the charging cover would be difficult to disassemble without damaging the coils or fine connecting wires. The glue securing the innards looks like it's impregnable, but rest assured... a little heat from a hair dryer loosens it up nicely. When that glue gets warm, the cover almost falls apart in your hands. I surely wouldn't want to forget and leave this thing lying in the sun on my car dash!
As for the changes... I found that the Nokia Charging cover for the 1020 wasn't the best design. The contacts inside were tensioned so that they make contact lightly with the phone's contacts, so about half the time I had to adjust or squeeze the cover to get it to charge on my Nokia charging pads. When I installed the coils in my Otterbox, I attached a tiny piece of 3M double sided foam core tape to the back side of the contact pad. This puts additional pressure on the contacts when the Otterbox is assembled so that the contacts are securely touching. So far I have had great results... no adjustment necessary.
I also found that the 1020 charging cover is much more sensitive to its position on the charging pad than my Lumia 920 was. And that hasn't changed with the Otterbox mod. I could just throw my 920 down on the pad and it would start charging... off center... sideways... it just charged. The 1020 charging cover (and now Otterbox charging cover!) is much more sensitive and will not charge unless it is centered on the pad just right. Couple that sensitivity with the weak contact points and it makes for a frustrating process to get the phone to charge wirelessly. The additional contact pressure from the foam core tape fixed the most troublesome part of the problem. So now I just have to be aware of how I center the phone on the charging pad.
- By Tom Niccoli in forum Nokia Lumia 822Replies: 2Last Post: 08-26-2013, 01:08 PM
- By Credo93 in forum Nokia Lumia 920Replies: 14Last Post: 08-21-2013, 08:14 AM
- By magictriangle in forum Nokia Lumia 925Replies: 5Last Post: 08-21-2013, 01:06 AM
- By iz0d in forum Windows Phone 7Replies: 3Last Post: 08-20-2013, 12:11 AM